Import grbl v1.1h
diff --git a/grbl/examples/grblWrite_BuildInfo/grblWrite_BuildInfo.ino b/grbl/examples/grblWrite_BuildInfo/grblWrite_BuildInfo.ino
new file mode 100644
index 0000000..2759d47
--- /dev/null
+++ b/grbl/examples/grblWrite_BuildInfo/grblWrite_BuildInfo.ino
@@ -0,0 +1,109 @@
+/***********************************************************************
+This sketch writes a `$I` build info string directly into Arduino EEPROM
+
+To use:
+- Just alter the "build_info_line" string to whatever you'd like. Then
+ compile and upload this sketch to your Arduino.
+
+- If your Arduino is blinking slowly, your string has already been
+ written to your EEPROM and been verified by checksums! That's it!
+
+- If you Arduino LED is blinking fast, something went wrong and the
+ checksums don't match. You can optionally connect to the Arduino via
+ the serial monitor, and the sketch will show what its doing.
+
+NOTE: This sketch is provided as a tool template for OEMs who may need
+to restrict users from altering their build info, so they can place
+important product information here when enabling the restriction.
+
+NOTE: When uploading Grbl to the Arduino with this sketch on it, make
+sure you see the slow blink before you start the upload process. This
+ensures you aren't flashing Grbl when it's in mid-write of the EEPROM.
+
+Copyright (c) 2016 Sungeun K. Jeon for Gnea Research LLC
+Released under the MIT-license. See license.txt for details.
+***********************************************************************/
+
+#include <avr/pgmspace.h>
+#include <EEPROM.h>
+
+#define SERIAL_BAUD_RATE 115200
+#define LINE_LENGTH 80U // Grbl line length
+#define BYTE_LOCATION 942U // Grbl build info EEPROM address.
+
+
+// ----- CHANGE THIS LINE -----
+
+char build_info_line[LINE_LENGTH] = "Testing123.";
+
+// -----------------------------
+
+
+uint8_t status = false;
+int ledPin = 13; // LED connected to digital pin 13
+
+void setup() {
+ Serial.begin(SERIAL_BAUD_RATE);
+ delay(500);
+
+ uint32_t address = BYTE_LOCATION;
+ uint32_t size = LINE_LENGTH;
+ char *write_pointer = (char*)build_info_line;
+ uint8_t write_checksum = 0;
+ for (; size>0; size--) {
+ write_checksum = (write_checksum << 1) || (write_checksum >> 7);
+ write_checksum += *write_pointer;
+ EEPROM.put(address++, *(write_pointer++));
+ }
+ EEPROM.put(address,write_checksum);
+
+ Serial.print(F("-> Writing line to EEPROM: '"));
+ Serial.print(build_info_line);
+ Serial.print(F("'\n\r-> Write checksum: "));
+ Serial.println(write_checksum,DEC);
+
+ size = LINE_LENGTH;
+ address = BYTE_LOCATION;
+ uint8_t data = 0;
+ char read_line[LINE_LENGTH];
+ char *read_pointer = (char*)read_line;
+ uint8_t read_checksum = 0;
+ uint8_t stored_checksum = 0;
+ for(; size > 0; size--) {
+ data = EEPROM.read(address++);
+ read_checksum = (read_checksum << 1) || (read_checksum >> 7);
+ read_checksum += data;
+ *(read_pointer++) = data;
+ }
+ stored_checksum = EEPROM.read(address);
+
+ Serial.print(F("<- Reading line from EEPROM: '"));
+ Serial.print(read_line);
+ Serial.print("'\n\r<- Read checksum: ");
+ Serial.println(read_checksum,DEC);
+
+ if ((read_checksum == write_checksum) && (read_checksum == stored_checksum)) {
+ status = true;
+ Serial.print(F("SUCCESS! All checksums match!\r\n"));
+ } else {
+ if (write_checksum != stored_checksum) {
+ Serial.println(F("ERROR! Write and stored EEPROM checksums don't match!"));
+ } else {
+ Serial.println(F("ERROR! Read and stored checksums don't match!"));
+ }
+ }
+ pinMode(ledPin, OUTPUT); // sets the digital pin as output
+}
+
+void loop() {
+ // Blink to let user know EEPROM write status.
+ // Slow blink is 'ok'. Fast blink is an 'error'.
+ digitalWrite(ledPin, HIGH); // sets the LED on
+ if (status) { delay(1500); } // Slow blink
+ else { delay(100); } // Rapid blink
+ digitalWrite(ledPin, LOW); // sets the LED off
+ if (status) { delay(1500); }
+ else { delay(100); }
+}
+
+